As of
2009 | 2008 | 2007 | 2006 | 2004
- Katsushi Furutani, Atsushi Furuta: Comparison of Driving Performance of
Piezoelectric Actuator - Current Pulse Drive and Voltage Linear Drive -,
Service Robotics and Mechatronics, pp. 183-188 (2009)
- Katsushi Furutani, Taizo Makino: Influence of Matrix Circuit Switching
Device Junction Capacitance on Piezoelectric Actuator Drive Performance,
International Journal of Automation Technology, 3, 3, pp. 313-318 (2009)
- Katsushi Furutani, Hiroshi Tachi, Mitsuru Saito: Linear Measurement and
Training Device for Leg Evaluation, International Journal of Automation
Technology, 3, 3, pp. 298-303 (2009)
- Katsushi Furutani, Hiromichi Sato, Masayuki Suzuki: Influence of electrical
conditions on performance of electircal discharge machining with powder
suspended in working oil for titanium carbide deposition process, International
Journal of Advanced Manufacturing Technology, 40, 11-12, pp. 1093-1101
(2009)
Go to Top
- Katsushi Furutani, Hideaki Maeda: Machining a glass rod with a lathe-type
electro-chemical discharge machine, Journal of Micromechanics and Microengineering,
18, 6, 065006, pp. 1-8 (2008)
- Katsushi Furutani, Yasuo Murase: Fabrication of Wire Saw with Patterned
Hard Bamps by Electrical Discharge Machining with Powder Suspended in WorkingOil,
Manufacturing Systems and Technologies for the New Frontier (The 41st CIRP
Confeernce on Manufacturing Systems), Tokyo, Japan, pp. 361-364 (2008)
- Katsushi Furutani, Noriyuki Ohta: Displacement Monitoring of Stacked Piezoelectric Actuator by Observing Induced Charge,
International Journal of Automation Technology, 2, 1, pp. 12-17 (2008)
Go to Top
- Yoshitaka Mieda, Katsushi Furutani: Liquid Crystal Actuator Using Nematic
π Cell, Journal of Robotics and Mechatronics, 19, 5, pp. 524-527 (2007)
- Yoshitaka Mieda, Katsushi Furutani:
A self-consistent approach for SmA-SmC* phase transition, Philosophical Magazine,
87, 24, pp. 3555-3564 (2007)
Go to Top
- Katsushi Furutani, Katsuhiko Iida: A driving method of piezoelectric actuator using current pulses,
Measurement Science and Technology, 17, 9, pp. 2387-2394 (2006)
Go to Top
- Katsushi
Furutani, Michio Suzuki, Ryusei Kudoh: Nanometre-cutting machine using a Stewart-platform parallel mechanism,
Measurement Science and Technology, 15, 2, pp. 467-474 (2004)
- Katsushi Furutani, Hirotaka Sunada:
Fabrication of Abrasive Layer Using Dispersion of Hard Powder by Electrical Discharge Machining (2nd Report)
- Evaluation of Abrasive Layer through Grinding Process -,
International Journal of Electrical Machining, 9, pp. 21-26 (2004).
- Katsushi Furutani, Hirotaka Sunada: Fabrication of Abrasive Layer Using Dispersion of Hard Powder by Electrical Discharge Machining (1st Report) - Dispersion of Insulating Poweder into Deposit -,
International Journal of Electrical Machining, 9, pp. 15-20 (2004).
- Katsushi
Furutani, Noriyuki Ohta, Katsumi Kawagoe:
Coarse and fine positioning performance of an L-shaped seal mechanism with three degrees of freedom,
Measurement Science and Technology, 15, 1, pp. 103-111 (2004).
Go to Top
Go to top page of paper list
by Katsushi
Furutani